Electronic Boards
Showing 16–30 of 42 results
-
Fanatec
ElectroSeed MMWB H
The MMWB H board (MicroMod Wheel Board Hub) allows you to connect daughterboards in MicroMod format and offers unique features. Ideal for USB configurations with or without USB screens (like Vocore), it proposes filters and protections on USB input and output lines. To use it with a USB screen, you'll have to associate it with the Samd21J Hub daughter board, that includes a USB HUB.
It can also be used for USB configurations without screens, with a SamD21, SamD21J or SamD51 daughter board.
You'll find below in the description tab a table with the different daughter boards to help you choose the one corresponfing to your needs. All boards can work via USB or native connection with Fanatec or Thrustmaster bases. The management of Nextion screens, RGB LEDs and 7-segment displays is done using the SimHub software and needs a NRF Dongle to work wirelessly.
SKU: 682 -
MicroMod
ElectroSeed MMWB RB
The MMWB RB (MicroMod Wheel Board Radio Boost) allows you to connect daughterboards in MicroMod format and offers unique features. Ideal for wireless, battery powered configurations, it proposes a Lithium-Ion charging circuit (3A Max), as well as a Boost circuit to deliver 5v to Nextion screens or lots of RGB leds.
You'll find below in the description tab a table with the different daughter boards to help you choose the one corresponfing to your needs. All boards can work via USB or native connection with Fanatec or Thrustmaster bases. The management of Nextion screens, RGB LEDs and 7-segment displays is done using the SimHub software and needs a NRF Dongle to work wirelessly.
SKU: 542 -
Fanatec
ElectroSeed MMWB RQR
The MMWB RQR board (MicroMod Wheel Board Radio QR) allows you to connect radio daughterboards in MicroMod format and offers unique features. It's ideal for wireless QR powered configurations (Bases Moza, Simagic ou Fanatec).
You'll find below in the description tab a table with the different daughter boards to help you choose the one corresponfing to your needs. Only the SamD21J NRF daughter board can work at the same wirelessly and natively with a Fanatec or Thrustmaster bases. The management of Nextion screens, RGB LEDs and 7-segment displays is done using the SimHub software and will need a NRF Dongle to work wirelessly.
SKU: 681 -
Radio
ElectroSeed SamD21 WB Radio
The ElectroSeed SamD21 WB Radio board offers 31 inputs/outputs, including 14 analog inputs. 4 analog inputs have pull-up resistors, which allows direct connection of bodacs, thus adding the possibility of connecting 20 additional buttons.
5v power is available (if powered from a Moza or Simagic or other QR providing 5v) around the serial port to connect a Nextion screen or a 7-segment display. The 5v is also exposed to connect RGB leds. Screen and leds are managed with SimHub software, and requires an NRF Dongle to communicate with the PC.
Attention : this card is intended for use with a Moza, Simagic base or other system with induction power supply providing 5V. For use with battery, you will need to go to another card managing battery charging (Feather or XIAO Ble), or a card equipped with a 5V booster to power a screen or many LEDs (MMWB)
The following connectors are also proposed :
- A 5v power connector to connect to the Simagic or Moza bases (thanks to our Simagic and Moza Quick Releases), the radio version allowing native radio communication with Simagic bases (inputs only, 32 functions) or with Moza bases (inputs only, 64 functions)
- A 4-pin JST 2.0 connector to easily connect an aviation connector or a panel mount USB connector for firmware updates.
- A USB-C connector to program the board or connect a USB extension.
If you choose a customized firmware option, a NodeBlue package will be included with the board, so you can have any configuration you need. A configuration form will be sent after your order, so you can specify the desired programming. The board will be programmed accordingly and the wiring schematics will be provided. You can check here if your configuration is possible.
SKU: 661 -
USB
ElectroSeed SamD21 WB USB
The ElectroSeed SamD21 WB USB board offers 36 USB inputs/outputs, including 14 analog inputs. 4 analog inputs have pull-up resistors, which allows direct connection of bodacs, thus adding the possibility of connecting 20 additional buttons.
The 5v is available around the serial port to connect a Nextion screen or a 7-segment display. The 5v is also exposed to connect RGB leds. Screen and leds are managed with SimHub software.
The following connectors are also proposed :
- A 4-pin JST 2.0 connector to easily connect an aviation connector.
- A USB-C connector to program the board or connect a USB extension.
- A 2-pin JST 2.0 connector with 5v to power permanently button leds for example.
If you choose a customized firmware option, NodeBlue package is included with the board, so you can have any configuration you need. A configuration form will be sent after your order, so you can specify the desired programming. The board will be programmed accordingly and the wiring schematics will be provided. You can check here if your configuration is possible.
SKU: 648 -
Pedals
Electroseed Tiny Pedals Board
Pedals board with vibration motor control
This board, based on the SamD21 micro-controller, makes it possible to interface buttons/encoders, various sensors, and a NRF24L01 radio module. Two I2C ports and an SPI port are accessible, for example to connect 2 AS5600 magnetic angle sensors or a contactless magnetic sensorThis board also offers a motor control circuit, allowing the control of up to 2 vibration motors to simulate ABS, TC, etc., if the game sends this information, and by interfacing with SimHub software. The motors can be powered by USB or by a separate power supply (voltage between 4 and 16 V). The maximum current is 500 mA per motor, for a total power of 1 W max. Motor speeds are controlled by high frequency PWM signals, so commutation signals are inaudible.You will have access to 17 I/O including 13 analog inputs (12 bits). The inputs are 3.3 V and are not 5 V tolerant. The SamD21 operates at 48 MHz.A NodeBlue package is included with the board, so you can have any configuration you need. A configuration form will be sent after your order, so you can specify the desired programming. The board will be programmed accordingly and the wiring schematics will be provided.SKU: 628 -
MicroMod
MicroMod NRF52840
Featuring the nRF52840 SoC from Nordic Semiconductor, the SparkFun MicroMod nRF52840 Processor offers a powerful combination of ARM Cortex-M4 CPU and 2.4 GHz Bluetooth transceiver in the MicroMod form-factor with the M.2 MicroMod connector to allow you to plug in a compatible MicroMod Carrier Board with any number of peripherals.
The MicroMod nRF52840 Processor features the Raytac MDBT50Q-P1. This module includes an integrated trace antenna, fits the IC to an FCC and CE approved footprint along with including decoupling and timing mechanisms that would need to be designed into a circuit using the bare nRF52840 IC. The Bluetooth transceiver included on the nRF52840 boasts a BT 5.1 stack and supports Bluetooth 5, Bluetooth mesh, IEEE 802.15.4 (Zigbee & Thread) and 2.4Ghz RF wireless protocols (including Nordic's proprietary RF protocol) allowing you to pick which option works best for your application.
There's also two I2C buses, 2 SPI buses, eleven GPIO, dedicated digital, analog, PWM & PDM pins along with multiple serial UARTS to cover nearly all of your peripheral needs.
We have fixed a hardware bug on this board in order to be able to use the ADC for radiometric measures (potentiometers, etc.).
SKU: 605 -
MicroMod
MicroMod SamD21
With a 32-bit ARM Cortex-M0 MCU, the ElectroSee MicroMod SAMD21 Processor Board provides you with an economical and easy to use development platform. With the M.2 MicroMod connector, connecting your SAMD21 Processor is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards).
The ATSAMD21G18 used is a 32-bit ARM Cortex-M0, running up to 48 MHz, has 256 KB of flash memory, 32 KB of SRAM, 6 SERCOM interfaces, and other features. This MicroMod SAMD21 comes flashed with the UF2 bootloader.
SKU: 649 -
MicroMod
MicroMod SamD21J
With a 32-bit ARM Cortex-M0 MCU, the ElectroSee MicroMod SAMD21 Processor Board provides you with a powerful development platform that has the highest numer of inputs/outputs in the Micromod familly.
The microcontroler used is an ATSAMD21J18, a 32-bit ARM Cortex-M0, running at 48 MHz, has 256 KB of flash memory, 32 KB of SRAM, 6 SERCOM interfaces, and other features.
Number of inputs/outputs : 50 including 20 analog.
SKU: 676 -
MicroMod
MicroMod SamD21J H
With a 32-bit ARM Cortex-M0 MCU, the ElectroSee MicroMod SAMD21 Processor Board provides you with the highest numer of inputs/outputs in the Micromod familly. It also includes a USB hub, and exposes the secondary port on the USB host connexions of the Micromod standard. This hub is compatible with the USB 2.0 480 Mb/s High Speed standard, and allows to connect reliably USB screens like Vocore screens.
The microcontroler used is an ATSAMD21J18, a 32-bit ARM Cortex-M0, running at 48 MHz, has 256 KB of flash memory, 32 KB of SRAM, 6 SERCOM interfaces, and other features.
Number of inputs/outputs : 50 including 20 analog.
SKU: 684 -
MicroMod
MicroMod SamD21J NRF
With a 32-bit ARM Cortex-M0 MCU, the ElectroSeed MicroMod SAMD21J NRF Processor Board provides a powerfull and versatile platform. With the NRF24L01 radio module and its ceramic antenna, make your wireless projecy easily with a maximum of inputs.
The ATSAMD21J18 used is a 32-bit ARM Cortex-M0, running at 48 MHz, has 256 KB of flash memory, 32 KB of SRAM, 6 SERCOM interfaces, and other features.
Number of inputs/outputs : 45 including 16 analog.
SKU: 677 -
MicroMod
MicroMod SamD51
With a 32-bit ARM Cortex-M4F MCU, the SparkFun MicroMod SAMD51 Processor Board provides an economical and easy to use development platform if you're needing lots of power with minimal working space. With the M.2 MicroMod connector, connecting your SAMD51 Processor is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards). The SAMD51 is one of the most powerful and economical microcontrollers available so to be able to add it to your MicroMod Carrier Board is a huge advantage for your project!
The ATSAMD51J20 utilizes a 32-bit ARM Cortex-M4 processor with Floating Point Unit (FPU), running up to 120MHz, with 1 MB of flash memory, 256 KB of SRAM with ECC, 6 SERCOM interfaces, and other features
We have fixed a hardware bug on this board in order to be able to use the ADC for radiometric measures (potentiometers, etc.).
SKU: 606 -
Dongles
NRF Dongle
NRF52840 micro-controler based dongle.
This dongle can be used as a radio receiver and is compatible with all our radio boards (based on NRF24 modules or NRF52840).
The NRF52840 micro-controler includes an USB hardware controler which can be programmed to create a gaming device, a keyboard, a mouse, etc..
A standard Node Blue package is included with the dongle.
Dimensions :
– Length : 43 mm (including USB connector)
– Width : 18 mm
– Height : 9 mm
SKU: 358 -
Dongles
NRF Dongle (Pack of 50)
NRF52840 micro-controler based dongle.
This dongle can be used as a radio receiver and is compatible with all our radio boards (based on NRF24 modules or NRF52840).
The NRF52840 micro-controler includes an USB hardware controler which can be programmed to create a gaming device, a keyboard, a mouse, etc..
A Pro Node Blue package is included with each dongle.
Dimensions :
– Length : 43 mm (including USB connector)
– Width : 18 mm
– Height : 9 mm
SKU: 619
