-
×
Battery Case holder 18650
1 × 0,70 €
Subtotal: 0,70 €
Components
Showing 16–30 of 112 results
-
Power Supplies
Adafruit Miniboost 5V
This DC-DC boost converter step-up power module uses TPS61023 with a high switching frequency of 1 MHz, and an efficiency between 80% and 90%
– Input Voltage : 0.5V-5.5V
– Output voltage : 5V
– Max Current : 1A
– Dimensions: L * W * H = 17.8mm x 11.3mm x 5.6mm
SKU: 529 -
Joysticks
Analog Joystick
This component combines an analog joystick and a push button.
- Shaft Length: 7.7 mm
- Shaft Diameter: 4 mm
- Bushing Material: Metal + plastic
- Panel mount, bushing Thread of spacers : M3 x 4, central hole : 12 mm
Delivered mounted, only 3 inputs will be needed on your board (2 analog inputs for the 2 axis, 1 digital input for the button).
Package content :
– Component mounted on its board
– Spacers and screws
– Knob printed in PLA (optional)
– Dupont to dupont 5 pins cable (optional)
SKU: 502 -
Sensors
Angle sensor AS5600 ElectroSeed
Contactless AS5600 12 bits angle sensor, delivered with a magnet.
Allows you to make pedals or any other element requiring a robust angle sensor.
The angle range can be 360° but can also be reduced to 18° while keeping the full precision of the sensor.
Available interfaces are analog or I2C.
We recommand I2C, since it will give a better precision if the angle interval is reduced, and also the signal will be more protected against noise.
In analog mode, if you have a board that is already programmed for potentiometers, you can replace them with this type of sensor without reprogramming the board (but pay attention to the wiring which is different).
Power voltage :3.3V
Board dimensions: 22.6 mm x 23.2 mm, thickness 3.2 mm (including pcb and components)
Magnet dimension : Diameter 6mm, height 2.5 mm
Magnet to sensor distance : min 0 mm, max 5 mm
Documentation : http://www.electroseed.fr/docs/AS5600.pdf
Node Blue example (i2C) : https://www.electroseed.fr/shop/gui/index.php?file=examples/06-Sensors/AS5600_HID.txt
SKU: 346 -
Resistors
Bodac Pack
The Bodac is a system that allows to implement several buttons on a single analog input, with the possibility to have several buttons pressed at the same time. The "usual" systems (resistors ladders or matrix without diodes), do not allow to press several buttons at a time.
The benefit of the Bodac compared to a button matrix with diodes is a simpler wiring: a resistance between each button pin, and a single wire between each button. The optional cable incorporates the common resistance at the connector level, allowing only 2 wires to come out of the board.
This pack of 1% precision resistors allows to create a Bodac with 5 buttons or less.
WARNING : We don't provide any source code to use this product, we recommend to use NodeBlue which proposes a dedicated module.
To start easily, you can refer to this NodeBlue example : https://www.electroseed.fr/shop/gui/index.php?file=examples/02-Digital/BodacHID.txt
SKU: 66 -
Rotary Encoders
CTS Encoder 16 det./rev + Button
Rotary Encoder 16 detents / revolution, 1 pulses / detent, with push button
- Shaft Length: 25.4 mm (1")
- Shaft Diameter: 6.35 mm (0.250")
- Bushing Material: Metal
- Panel mount, hole diameter : 9.5 mm
- bushing Thread: 3/8-32 UNEF-2A
- Detent torque : 120 gf.cm (1.7 oz.in)
Manufacturer : CTS
Reference : 288V232F161B2
Link to Data sheet : https://www.electroseed.fr/docs/CTS288-2255.pdf
SKU: 334 -
Rotary Encoders
CTS Encoder 16 det/rev
Rotary Encoder 16 detents / revolution, 1 pulses / detent
- Shaft Length: 19.05 mm (0.75")
- Bushing Length : 6.35 mm (0.250")
- Shaft Diameter: 6.35 mm (0.250")
- Bushing Material: Metal
- Panel mount, hole diameter : 9.5 mm
- Bushing Thread: 3/8-32 UNEF-2A
- Detent torque : 300 gf.cm (4.1 oz.in)
Manufacturer : CTS
Reference : 288T232R161A2
Link to Data sheet : https://www.electroseed.fr/docs/CTS288-2255.pdf
SKU: 192
